ct action in tc(8)		     Linux		    ct action in tc(8)

NAME
       ct - tc connection tracking action

SYNOPSIS
       tc ... action ct commit [ force ] [ zone	 ZONE ] [ mark	MASKED_MARK ]
	       [ label	MASKED_LABEL ] [ nat  NAT_SPEC ]

       tc ... action ct [ nat ] [ zone	ZONE ]

       tc ... action ct clear


DESCRIPTION
       The ct action is a tc action for sending packets and interacting with
       the netfilter conntrack module.

       It can (as shown in the synopsis, in order):

       Send the packet to conntrack, and commit the connection, while
       configuring a 32bit mark, 128bit label, and src/dst nat.

       Send the packet to conntrack, which will mark the packet with the
       connection's state and configured metadata (mark/label), and execute
       previous configured nat.

       Clear the packet's of previous connection tracking state.


OPTIONS
       zone ZONE
	      Specify a conntrack zone number on which to send the packet to
	      conntrack.

       mark MASKED_MARK
	      Specify a masked 32bit mark to set for the connection (only
	      valid with commit).

       label MASKED_LABEL
	      Specify a masked 128bit label to set for the connection (only
	      valid with commit).

       nat NAT_SPEC
	      Where NAT_SPEC := {src|dst} addr addr1[-addr2] [port
	      port1[-port2]]

	      Specify src/dst and range of nat to configure for the connection
	      (only valid with commit).

	      src/dst - configure src or dst nat

	      addr1/addr2 - IPv4/IPv6 addresses

	      port1/port2 - Port numbers

       nat    Restore any previous configured nat.

       clear  Remove any conntrack state and metadata (mark/label) from the
	      packet (must only option specified).

       force  Forces conntrack direction for a previously committed
	      connections, so that current direction will become the original
	      direction (only valid with commit).


EXAMPLES
       Example showing natted firewall in conntrack zone 2, and conntrack mark
       usage:

       #Add ingress qdisc on eth0 and eth1 interfaces
       $ tc qdisc add dev eth0 ingress
       $ tc qdisc add dev eth1 ingress

       #Setup filters on eth0, allowing opening new connections in zone 2, and doing src nat + mark for each new connection
       $ tc filter add dev eth0 ingress prio 1 chain 0 proto ip flower ip_proto tcp ct_state -trk \
       action ct zone 2 pipe action goto chain 2
       $ tc filter add dev eth0 ingress prio 1 chain 2 proto ip flower ct_state +trk+new \
       action ct zone 2 commit mark 0xbb nat src addr 5.5.5.7 pipe action mirred egress redirect dev eth1
       $ tc filter add dev eth0 ingress prio 1 chain 2 proto ip flower ct_zone 2 ct_mark 0xbb ct_state +trk+est \
       action ct nat pipe action mirred egress redirect dev eth1

       #Setup filters on eth1, allowing only established connections of zone 2 through, and reverse nat (dst nat in this case)
       $ tc filter add dev eth1 ingress prio 1 chain 0 proto ip flower ip_proto tcp ct_state -trk \
       action ct zone 2 pipe action goto chain 1
       $ tc filter add dev eth1 ingress prio 1 chain 1 proto ip flower ct_zone 2 ct_mark 0xbb ct_state +trk+est \
       action ct nat pipe action mirred egress redirect dev eth0



SEE ALSO
       tc(8), tc-flower(8) tc-mirred(8)

AUTHORS
       Paul Blakey <paulb@mellanox.com>

       Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>

       Yossi Kuperman <yossiku@mellanox.com>

iproute2			  14 May 2020		    ct action in tc(8)