ManPages Pro - Translated Unix Manual Pages

tc-cake(8)

Original

English • 619 lines

CAKE(8) Linux CAKE(8)

NAME
CAKE - Common Applications Kept Enhanced (CAKE)

DESCRIPTION
CAKE (Common Applications Kept Enhanced) is a shaping-capable queue
discipline which uses both AQM and FQ. It combines COBALT, which is an
AQM algorithm combining Codel and BLUE, a shaper which operates in
deficit mode, and a variant of DRR++ for flow isolation. 8-way set-
associative hashing is used to virtually eliminate hash collisions.
Priority queuing is available through a simplified diffserv
implementation. Overhead compensation for various encapsulation
schemes is tightly integrated.

All settings are optional; the default settings are chosen to be
sensible in most common deployments. Most people will only need to set
the bandwidth parameter to get useful results, but reading the Overhead
Compensation and Round Trip Time sections is strongly encouraged.

SHAPER PARAMETERS
CAKE uses a deficit-mode shaper, which does not exhibit the initial
burst typical of token-bucket shapers. It will automatically burst
precisely as much as required to maintain the configured throughput.
As such, it is very straightforward to configure.

unlimited (default)
No limit on the bandwidth.

bandwidth RATE
Set the shaper bandwidth. See tc(8) or examples below for
details of the RATE value.

autorate-ingress
Automatic capacity estimation based on traffic arriving at this
qdisc. This is most likely to be useful with cellular links,
which tend to change quality randomly. A bandwidth parameter
can be used in conjunction to specify an initial estimate. The
shaper will periodically be set to a bandwidth slightly below
the estimated rate. This estimator cannot estimate the
bandwidth of links downstream of itself.

OVERHEAD COMPENSATION PARAMETERS
The size of each packet on the wire may differ from that seen by Linux.
The following parameters allow CAKE to compensate for this difference
by internally considering each packet to be bigger than Linux informs
it. To assist users who are not expert network engineers, keywords
have been provided to represent a number of common link technologies.

Manual Overhead Specification
overhead BYTES
Adds BYTES to the size of each packet. BYTES may be negative;
values between -64 and 256 (inclusive) are accepted.

mpu BYTES
Rounds each packet (including overhead) up to a minimum length
BYTES. BYTES may not be negative; values between 0 and 256
(inclusive) are accepted.

atm
Compensates for ATM cell framing, which is normally found on
ADSL links. This is performed after the overhead parameter
above. ATM uses fixed 53-byte cells, each of which can carry 48
bytes payload.

ptm
Compensates for PTM encoding, which is normally found on VDSL2
links and uses a 64b/65b encoding scheme. It is even more
efficient to simply derate the specified shaper bandwidth by a
factor of 64/65 or 0.984. See ITU G.992.3 Annex N and IEEE 802.3
Section 61.3 for details.

noatm
Disables ATM and PTM compensation.

Failsafe Overhead Keywords
These two keywords are provided for quick-and-dirty setup. Use them if
you can't be bothered to read the rest of this section.

raw (default)
Turns off all overhead compensation in CAKE. The packet size
reported by Linux will be used directly.

Other overhead keywords may be added after "raw". The effect of
this is to make the overhead compensation operate relative to
the reported packet size, not the underlying IP packet size.

conservative
Compensates for more overhead than is likely to occur on any
widely-deployed link technology. Equivalent to overhead 48 atm.

ADSL Overhead Keywords
Most ADSL modems have a way to check which framing scheme is in use.
Often this is also specified in the settings document provided by the
ISP. The keywords in this section are intended to correspond with
these sources of information. All of them implicitly set the atm flag.

pppoa-vcmux
Equivalent to overhead 10 atm

pppoa-llc
Equivalent to overhead 14 atm

pppoe-vcmux
Equivalent to overhead 32 atm

pppoe-llcsnap
Equivalent to overhead 40 atm

bridged-vcmux
Equivalent to overhead 24 atm

bridged-llcsnap
Equivalent to overhead 32 atm

ipoa-vcmux
Equivalent to overhead 8 atm

ipoa-llcsnap
Equivalent to overhead 16 atm

See also the Ethernet Correction Factors section below.

VDSL2 Overhead Keywords
ATM was dropped from VDSL2 in favour of PTM, which is a much more
straightforward framing scheme. Some ISPs retained PPPoE for
compatibility with their existing back-end systems.

pppoe-ptm
Equivalent to overhead 30 ptm

PPPoE: 2B PPP + 6B PPPoE +
ETHERNET: 6B dest MAC + 6B src MAC + 2B ethertype + 4B Frame
Check Sequence +
PTM: 1B Start of Frame (S) + 1B End of Frame (Ck) + 2B TC-CRC
(PTM-FCS)

bridged-ptm
Equivalent to overhead 22 ptm

ETHERNET: 6B dest MAC + 6B src MAC + 2B ethertype + 4B Frame
Check Sequence +
PTM: 1B Start of Frame (S) + 1B End of Frame (Ck) + 2B TC-CRC
(PTM-FCS)

See also the Ethernet Correction Factors section below.

DOCSIS Cable Overhead Keyword
DOCSIS is the universal standard for providing Internet service over
cable-TV infrastructure.

In this case, the actual on-wire overhead is less important than the
packet size the head-end equipment uses for shaping and metering. This
is specified to be an Ethernet frame including the CRC (aka FCS).

docsis
Equivalent to overhead 18 mpu 64 noatm

Ethernet Overhead Keywords
ethernet
Accounts for Ethernet's preamble, inter-frame gap, and Frame
Check Sequence. Use this keyword when the bottleneck being
shaped for is an actual Ethernet cable. Equivalent to overhead
38 mpu 84 noatm

ether-vlan
Adds 4 bytes to the overhead compensation, accounting for an
IEEE 802.1Q VLAN header appended to the Ethernet frame header.
NB: Some ISPs use one or even two of these within PPPoE; this
keyword may be repeated as necessary to express this.

ROUND TRIP TIME PARAMETERS
Active Queue Management (AQM) consists of embedding congestion signals
in the packet flow, which receivers use to instruct senders to slow
down when the queue is persistently occupied. CAKE uses ECN signalling
when available, and packet drops otherwise, according to a combination
of the Codel and BLUE AQM algorithms called COBALT.

Very short latencies require a very rapid AQM response to adequately
control latency. However, such a rapid response tends to impair
throughput when the actual RTT is relatively long. CAKE allows
specifying the RTT it assumes for tuning various parameters. Actual
RTTs within an order of magnitude of this will generally work well for
both throughput and latency management.

At the 'lan' setting and below, the time constants are similar in
magnitude to the jitter in the Linux kernel itself, so congestion might
be signalled prematurely. The flows will then become sparse and total
throughput reduced, leaving little or no back-pressure for the fairness
logic to work against. Use the "metro" setting for local lans unless
you have a custom kernel.

rtt TIME
Manually specify an RTT.

datacentre
For extremely high-performance 10GigE+ networks only.
Equivalent to rtt 100us.

lan
For pure Ethernet (not Wi-Fi) networks, at home or in the
office. Don't use this when shaping for an Internet access
link.
Equivalent to rtt 1ms.

metro
For traffic mostly within a single city.
Equivalent to rtt 10ms.

regional
For traffic mostly within a European-sized country.
Equivalent to rtt 30ms.

internet (default)
This is suitable for most Internet traffic.
Equivalent to rtt 100ms.

oceanic
For Internet traffic with generally above-average latency, such
as that suffered by Australasian residents.
Equivalent to rtt 300ms.

satellite
For traffic via geostationary satellites.
Equivalent to rtt 1000ms.

interplanetary
So named because Jupiter is about 1 light-hour from Earth. Use
this to (almost) completely disable AQM actions.
Equivalent to rtt 3600s.

FLOW ISOLATION PARAMETERS
With flow isolation enabled, CAKE places packets from different flows
into different queues, each of which carries its own AQM state.
Packets from each queue are then delivered fairly, according to a DRR++
algorithm which minimizes latency for "sparse" flows. CAKE uses a set-
associative hashing algorithm to minimize flow collisions.

These keywords specify whether fairness based on source address,
destination address, individual flows, or any combination of those is
desired.

flowblind
Disables flow isolation; all traffic passes through a single
queue for each tin.

srchost
Flows are defined only by source address. Could be useful on
the egress path of an ISP backhaul.

dsthost
Flows are defined only by destination address. Could be useful
on the ingress path of an ISP backhaul.

hosts
Flows are defined by source-destination host pairs. This is
host isolation, rather than flow isolation.

flows
Flows are defined by the entire 5-tuple of source address,
destination address, transport protocol, source port and
destination port. This is the type of flow isolation performed
by SFQ and fq_codel.

dual-srchost
Flows are defined by the 5-tuple, and fairness is applied first
over source addresses, then over individual flows. Good for use
on egress traffic from a LAN to the internet, where it'll
prevent any one LAN host from monopolising the uplink,
regardless of the number of flows they use.

dual-dsthost
Flows are defined by the 5-tuple, and fairness is applied first
over destination addresses, then over individual flows. Good
for use on ingress traffic to a LAN from the internet, where
it'll prevent any one LAN host from monopolising the downlink,
regardless of the number of flows they use.

triple-isolate (default)
Flows are defined by the 5-tuple, and fairness is applied over
source *and* destination addresses intelligently (ie. not merely
by host-pairs), and also over individual flows. Use this if
you're not certain whether to use dual-srchost or dual-dsthost;
it'll do both jobs at once, preventing any one host on *either*
side of the link from monopolising it with a large number of
flows.

nat
Instructs Cake to perform a NAT lookup before applying flow-
isolation rules, to determine the true addresses and port
numbers of the packet, to improve fairness between hosts
"inside" the NAT. This has no practical effect in "flowblind"
or "flows" modes, or if NAT is performed on a different host.

nonat (default)
Cake will not perform a NAT lookup. Flow isolation will be
performed using the addresses and port numbers directly visible
to the interface Cake is attached to.

PRIORITY QUEUE PARAMETERS
CAKE can divide traffic into "tins" based on the Diffserv field. Each
tin has its own independent set of flow-isolation queues, and is
serviced based on a WRR algorithm. To avoid perverse Diffserv marking
incentives, tin weights have a "priority sharing" value when bandwidth
used by that tin is below a threshold, and a lower "bandwidth sharing"
value when above. Bandwidth is compared against the threshold using
the same algorithm as the deficit-mode shaper.

Detailed customisation of tin parameters is not provided. The
following presets perform all necessary tuning, relative to the current
shaper bandwidth and RTT settings.

besteffort
Disables priority queuing by placing all traffic in one tin.

precedence
Enables legacy interpretation of TOS "Precedence" field. Use of
this preset on the modern Internet is firmly discouraged.

diffserv4
Provides a general-purpose Diffserv implementation with four
tins:

• Bulk (CS1, LE in kernel v5.9+), 6.25% threshold, generally low
priority.
• Best Effort (general), 100% threshold.
• Video (AF4x, AF3x, CS3, AF2x, CS2, TOS4, TOS1), 50% threshold.
• Voice (CS7, CS6, EF, VA, CS5, CS4), 25% threshold.

diffserv3 (default)
Provides a simple, general-purpose Diffserv implementation with
three tins:

• Bulk (CS1, LE in kernel v5.9+), 6.25% threshold, generally low
priority.
• Best Effort (general), 100% threshold.
• Voice (CS7, CS6, EF, VA, TOS4), 25% threshold, reduced Codel
interval.

fwmark MASK
This options turns on fwmark-based overriding of CAKE's tin
selection. If set, the option specifies a bitmask that will be
applied to the fwmark associated with each packet. If the result
of this masking is non-zero, the result will be right-shifted by
the number of least-significant unset bits in the mask value,
and the result will be used as a the tin number for that packet.
This can be used to set policies in a firewall script that will
override CAKE's built-in tin selection.

OTHER PARAMETERS
ingress
Indicates that CAKE is running in ingress mode (i.e. running on
the downlink of a connection). This changes the shaper to also
count dropped packets as data transferred, as these will have
already traversed the link before CAKE can choose what to do
with them.

In addition, the AQM will be tuned to always keep at least two
packets queued per flow. The reason for this is that retransmits
are more expensive in ingress mode, since dropped packets have
to traverse the link again; thus, keeping a minimum number of
packets queued will improve throughput in cases where the number
of active flows are so large that they saturate the link even at
their minimum window size.

memlimit LIMIT
Limit the memory consumed by Cake to LIMIT bytes. Note that this
does not translate directly to queue size (so do not size this
based on bandwidth delay product considerations, but rather on
worst case acceptable memory consumption), as there is some
overhead in the data structures containing the packets,
especially for small packets.

By default, the limit is calculated based on the bandwidth and
RTT settings.

wash
Traffic entering your diffserv domain is frequently mis-marked
in transit from the perspective of your network, and traffic
exiting yours may be mis-marked from the perspective of the
transiting provider.

Apply the wash option to clear all extra diffserv (but not ECN
bits), after priority queuing has taken place.

If you are shaping inbound, and cannot trust the diffserv
markings (as is the case for Comcast Cable, among others), it is
best to use a single queue "besteffort" mode with wash.

split-gso
This option controls whether CAKE will split General
Segmentation Offload (GSO) super-packets into their on-the-wire
components and dequeue them individually.

Super-packets are created by the networking stack to improve
efficiency. However, because they are larger they take longer
to dequeue, which translates to higher latency for competing
flows, especially at lower bandwidths. CAKE defaults to
splitting GSO packets to achieve the lowest possible latency. At
link speeds higher than 10 Gbps, setting the no-split-gso
parameter can increase the maximum achievable throughput by
retaining the full GSO packets.

OVERRIDING CLASSIFICATION WITH TC FILTERS
CAKE supports overriding of its internal classification of packets
through the tc filter mechanism. Packets can be assigned to different
priority tins by setting the priority field on the skb, and the flow
hashing can be overridden by setting the classid parameter.

Tin override
To assign a priority tin, the major number of the priority field needs
to match the qdisc handle of the cake instance; if it does, the minor
number will be interpreted as the tin index. For example, to classify
all ICMP packets as 'bulk', the following filter can be used:

# tc qdisc replace dev eth0 handle 1: root cake diffserv3
# tc filter add dev eth0 parent 1: protocol ip prio 1 \
u32 match icmp type 0 0 action skbedit priority 1:1

Flow hash override
To override flow hashing, the classid can be set. CAKE will interpret
the major number of the classid as the host hash used in host isolation
mode, and the minor number as the flow hash used for flow-based
queueing. One or both of those can be set, and will be used if the
relevant flow isolation parameter is set (i.e., the major number will
be ignored if CAKE is not configured in hosts mode, and the minor
number will be ignored if CAKE is not configured in flows mode).

This example will assign all ICMP packets to the first queue:

# tc qdisc replace dev eth0 handle 1: root cake
# tc filter add dev eth0 parent 1: protocol ip prio 1 \
u32 match icmp type 0 0 classid 0:1

If only one of the host and flow overrides is set, CAKE will compute
the other hash from the packet as normal. Note, however, that the host
isolation mode works by assigning a host ID to the flow queue; so if
overriding both host and flow, the same flow cannot have more than one
host assigned. In addition, it is not possible to assign different
source and destination host IDs through the override mechanism; if a
host ID is assigned, it will be used as both source and destination
host.

EXAMPLES
# tc qdisc delete root dev eth0
# tc qdisc add root dev eth0 cake bandwidth 100Mbit ethernet
# tc -s qdisc show dev eth0

qdisc cake 1: root refcnt 2 bandwidth 100Mbit diffserv3 triple-isolate rtt 100.0ms noatm overhead 38 mpu 84
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
memory used: 0b of 5000000b
capacity estimate: 100Mbit
min/max network layer size: 65535 / 0
min/max overhead-adjusted size: 65535 / 0
average network hdr offset: 0

Bulk Best Effort Voice
thresh 6250Kbit 100Mbit 25Mbit
target 5.0ms 5.0ms 5.0ms
interval 100.0ms 100.0ms 100.0ms
pk_delay 0us 0us 0us
av_delay 0us 0us 0us
sp_delay 0us 0us 0us
pkts 0 0 0
bytes 0 0 0
way_inds 0 0 0
way_miss 0 0 0
way_cols 0 0 0
drops 0 0 0
marks 0 0 0
ack_drop 0 0 0
sp_flows 0 0 0
bk_flows 0 0 0
un_flows 0 0 0
max_len 0 0 0
quantum 300 1514 762

After some use:
# tc -s qdisc show dev eth0

qdisc cake 1: root refcnt 2 bandwidth 100Mbit diffserv3 triple-isolate rtt 100.0ms noatm overhead 38 mpu 84
Sent 44709231 bytes 31931 pkt (dropped 45, overlimits 93782 requeues 0)
backlog 33308b 22p requeues 0
memory used: 292352b of 5000000b
capacity estimate: 100Mbit
min/max network layer size: 28 / 1500
min/max overhead-adjusted size: 84 / 1538
average network hdr offset: 14

Bulk Best Effort Voice
thresh 6250Kbit 100Mbit 25Mbit
target 5.0ms 5.0ms 5.0ms
interval 100.0ms 100.0ms 100.0ms
pk_delay 8.7ms 6.9ms 5.0ms
av_delay 4.9ms 5.3ms 3.8ms
sp_delay 727us 1.4ms 511us
pkts 2590 21271 8137
bytes 3081804 30302659 11426206
way_inds 0 46 0
way_miss 3 17 4
way_cols 0 0 0
drops 20 15 10
marks 0 0 0
ack_drop 0 0 0
sp_flows 2 4 1
bk_flows 1 2 1
un_flows 0 0 0
max_len 1514 1514 1514
quantum 300 1514 762

SEE ALSO
tc(8), tc-codel(8), tc-fq_codel(8), tc-htb(8)

AUTHORS
Cake's principal author is Jonathan Morton, with contributions from
Tony Ambardar, Kevin Darbyshire-Bryant, Toke Høiland-Jørgensen,
Sebastian Moeller, Ryan Mounce, Dean Scarff, Nils Andreas Svee, and
Dave Täht.

This manual page was written by Loganaden Velvindron. Please report
corrections to the Linux Networking mailing list
<netdev@vger.kernel.org>.

iproute2 19 July 2018 CAKE(8)

tc-cake(8)

CAKE \- Common Applications Kept Enhanced (CAKE)

0popularity

System Information

iproute2 1.0.0

Updated 19 July 2018

Maintained by Unknown

tc-cake(8)

System Information

Actions